Vespa 12v Conversion wiring loom for Large Frame Smallframe 50 -125 VBA to Rally

£72.60 Buy It Now, FREE Shipping, 30-Day Returns, eBay Money Back Guarantee
Seller: Top-Rated Seller vespajets ✉️ (23,960) 99.9%, Location: Colchester, GB, Ships to: GB & many other countries, Item: 165589146884 Vespa 12v Conversion wiring loom for Large Frame Smallframe 50 -125 VBA to Rally.

Vespa 12v Conversion wiring loom for Large Frame Smallframe 50 -125 VBA to Rally

Vespa 12v Conversion wiring loom for Large Frame Smallframe 50 -125 VBA to Rally

Wiring loom set for conversion

(incl. light switch)

-BGM PRO-

, Vespa AC conversion to electronic ignition- Vespa Smallframe V50, 50N, PV125, ET3, Vespa Largeframe Sprint, Rally, TS, GT, GTR, GL, Super, GS160, SS180, VNA, VNB, VBA, VBB

Description Conversion wiring harness for conversion to: PX alternator or PX engine in Rally, Sprint, VBB, Super, VNA, VNB, etc. PK alternator or PK engine in V50, Primavera, ET3, V90 etc. The conversion to a more modern alternator/ignition type is a proven means to be more durable and safer on the road. The contact-free CDI ignitions are almost indestructible and reliable, and the light output with a modern, regulator-supported, on-board electrical system is many times higher, since not only is the voltage increased from 6Volt to 12Volt, but the ignition base plate can also produce more power in general. Therefore it is necessary to adjust the wiring harness, because in modern electrics the alternators have all light coils connected in series for maximum power output and only one live cable is left as output for the on-board voltage. This is then led to the voltage regulator, which limits the on-board voltage to constant 12-13Volt. This effectively prevents the dreaded domino effect of the old electrical system, where all bulbs burn out one after the other after a defect of one. Only after the regulator is the current then conducted to the individual consumers. By this technology also a very high performance alternator can be used like e.g. our BGM ignition base plate, which already guarantees a high light yield and ignition performance at low speeds. To use such an alternator in the old chassis one needs therefore a suitable wiring harness. Our retrofit wiring harness is exactly the right thing and can be used very universally. It is based on an electrical system reduced to the most necessary, which lights the horn/ratchet, headlights/dipped headlights and the rear/brake lights. Optionally, the installation of a flasher relay is possible, the wiring harness is already prepared for this. In connection with our BGM 12Volt voltage regulator, this results in a very modern on-board electrical system which, in addition to a brilliant and powerful light output, also has gimmicks such as a DC output for the charging function of a mobile phone or e.g. a navigation device. By using our conversion wiring harness, no battery is needed anymore. A possibly existing 6V ratchet can still be used, it can cope with the occasional 12V without problems. Further technical information is stored in our wiring diagram. reliable electronic ignition - never again adjust contacts very high light output with 12V on-board voltage optional direct current for the charging function of a mobile phone, navigation device Please note: With very old vehicles space problems may occur due to the larger cable cross-sections of the conversion wiring harness used. This especially in the area of the tube duct for the rear light and in the steering head area. For safety reasons we do not want to use smaller cable cross sections. Wiring diagram: See "Downloads" Available as set with matching light switch for: Vespa Smallframe V50 Special Vespa Smallframe V50, 50N, PV125, ET3, Vespa Largeframe Sprint, Rally, TS, GT, GTR, GL, Super, GS160, SS180, VNA, VNB, VBA, VBB Note: A brake light switch type "normally open" is required. https://www.scooter-center.com/media/pdf/79/a4/19/Einbauanleitung_Fitting_instructions_.pdf  

Shipping

Shipping cost:
All our items on ebay include basic free postage

Upgrading the postage £10.00 the items will be sent Royal Mail special delivery

or UPS which is usually next day if sent early enough

Delivery time

small items are posted royal mail 48 or tracked 48 usually 2-3 days delivery

more expensive items are posted using UPS which are 1-2 days delivery

Larger items such as floor runners and legshield trims are posted by EVRI 2-3 days

 

Payment

We accept the following payment methods:

  • Paypal
  • call for other options

Please contact us if you have any questions. Tony 07810011361, 07868296364

Service

 

  • Condition: New
  • Brand: BGM
  • Manufacturer Part Number: 9077011 (BGM)
  • Country/Region of Manufacture: Germany

PicClick Insights - Vespa 12v Conversion wiring loom for Large Frame Smallframe 50 -125 VBA to Rally PicClick Exclusive

  •  Popularity - 2 watchers, 0.0 new watchers per day, 618 days for sale on eBay. Good amount watching. 4 sold, 1 available.
  •  Best Price -
  •  Seller - 23,960+ items sold. 0.1% negative feedback. Top-Rated Plus! Top-Rated Seller, 30-day return policy, ships in 1 business day with tracking.

People Also Loved PicClick Exclusive