Universal Solid State Relay (SSR) 6-32V, 40,80A

EUR 87,01 Buy It Now Unsold, EUR 11,01 Shipping, 60-Day Returns, Pay with PayPal and you're fully protected.

Seller: sbs.sales (68) 100%, Location: Riga, default, Ships to: Worldwide, Item: 282848743574 SSR (Low/Over Voltage Disconnect) in epoxy sealed ABS plastic case with USB for easy setup model: SBS 6-32HA-USB To protect batteries against over discharging. This unit is perfect for any kind of load where lightweight and small size is important. Features Low power MCU with 12 bit ADC conversion and micro USB connector on board. Fully customizable with BatMan manager software for any battery requirements. Solid state switch with 'soft start' feature (multiple N-ch MOSFETs on positive side). Draws only 0.7 mA when OFF and 1.5 mA when ON state!!! Two color (red, green) LEDs with multiple status indication patterns. Remote ON/OFF socket (JST XH 2.0-3 Pin). Connector with 15cm cable included. Two open drain (aka "open collector") outputs socket (JST XH 2.0-3 Pin) for alarm or other needs. Connector with 15cm cable included. Description Real-time input voltage and status monitoring in BatMan manager software. Device input voltage, status and all parameter changes are applied in real-time. Multiple devices simultaneously are supported. Wide range Cut-Off and Reconnect voltage level adjustments. The following set points can be set: Low voltage cut-off and reconnect with or without delay from 10 ms to 10 min Over voltage cut-off and reconnect with or without delay from 10 ms to 10 min Working range min, max. This gives immediate action without delay in case you set delays for LVD or OVD cut-off, but voltage drops too fast. All parameter changes are applied in real-time. Remote control connector to force ON/OFF states. If you short these pins to GND (black wire) than you will force the module in one of ON/OFF states. OFF pin has higher priority. If both are shortened then module will be in OFF state. This is handy if you need to control the load or use this module just as relay in any DC environment. Normally you can leave these pins opened. It is also possible to override these pins in manager software. Two open drain outputs to drive alarm device or other needs. Output 1 is active when delay before cut-off is used. This output can handle max 200 mA loads and is polyfuse protected. Output 2 currently not used, but may be used in feature. Thermal protection. Customisable temperature working range from -30° to 70° C (-22° to 158° F). This is true even in forced ON state. Over-current protection. (NOT short circuit protection - please use circuit breaker for that.) Will cut-off if over-current condition occurs. This feature is highly configurable, but has very rough current step gradation (one step is 1/5 of device max amp value). Will act like 'ideal diode'. If reverse current flow through MOSFET body diode is detected then device is forced to turn ON to eliminate power dissipation on body diode. Can be used as SSR relay. It can be easily configured as relay. Just drive it through remote port. Low self consumption This module has very low working current (max 0.7 mA when OFF and 1.5 mA when ON) Firmware upgrade is possible It is possible to upgrade devices firmware. If you find a bug or you need new features - send me a message and it will get fixed. NotesHere you can view a comparison table (as PDF doc.) for all actual models. Condition: New, Brand: BED-ELECTRONICS, MPN: SBS 6-32HA-USB

PicClick Insights PicClick Exclusive
  •  Popularity - 1 views, 0.0 views per day, 301 days on eBay. Normal amount of views. 0 sold, 12 available.
  •  Price -
  •  Seller - 68+ items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.
Similar Items