1 x NEMA 23 Stepper Motor, 200 Step, 4V@1.1A 3D Printer Arduino Raspberry Pi

£9.99 Buy It Now, £4.99 Shipping, eBay Money Back Guarantee
Seller: electronic_trade_sales ✉️ (2,137) 100%, Location: Nottingham, Nottinghamshire, GB, Ships to: GB & many other countries, Item: 222677041861 1 x NEMA 23 Stepper Motor, 200 Step, 4V@1.1A 3D Printer Arduino Raspberry Pi. You are looking at a powerful NEMA-23 stepper motor, ​ ​
  • Nice Quality 200 Step Motor with Ball Bearings front and rear
  • 18 mm Long Shaft 6.35 mm (0.25") diameter
  • Fitted with Pulley for Toothed Belt and Slotted Opto position sensor Disk 
  • Pulley easily removed
  • 500mm long high temperature connecting leads fitted with 6 pin 0.1" pitch connector
  • 6 wires allow universal Uni-polar and Bi-polar operation
  • Suitable for all drivers - Arduino/Pi/Chopper/DC drive
  • Low inductance windings allow high step rates with suitable drivers
  • Runs from any normal voltage from 2V upwards providing current is limited to 1.1A maximum per phase
  • 57 mm Square Flange  
  • 56.65 mm Body Diameter 
  • 4 M3 Fixing holes on 48 mm centres
  • 400g weight
  • Ideal for plotters, printers, robotics etc. 
  • Pulley size for toothed belt:   13mm diameter over teeth, 15 teeth at approx 3mm pitch
  • 9mm wide between flanges. 
  • Large Quantity Available if designing into a new project
These motors are Brand New and have been stored in manufacturers original trays wrapped in polythene with drying crystals. The motors run beautifully with lower current than the maximum 1.1A. There are two standard centre tapped windings and so the motors can be run as two phase bi-polar, or 4 phase unipolar modes - These are the normal most commonly used connection methods and so will work with all standard driver boards.  

Item specifics
Condition: New: A brand-new, unused, unopened and undamaged item in original retail packaging Brand: Astrosyn
Shaft Diameter: 6.35 mm/0.25 inches Nominal Rated Input Voltage: 5/12/24V
Protection Against Solids: Dust Protected, Most Wires and Screws, Tools and Thick Wire Actual Rated Input Voltage: 3 - 24
Wiring Configuration: Bi-polar or Uni-polar 6 Wire Connections Current Type: Pulsed
Full Load Amps: 1.1 Protection Against Liquids: Not Protected
Full Step Angle: 1.8 Degrees Rated Current per Phase: 1.1
Country/Region of Manufacture: Thailand Resistance per Phase: 3.6 Ohms
MPN: PJJQ26ZA-A

Thank you for looking, if you have any questions please ask or ring 01623 720730. Please see our other items for a wide range of Electronic components. 
  • Condition: New
  • Brand: Astrosyn
  • MPN: PJJQ26ZA-A
  • Actual Rated Input Voltage: 4V
  • Nominal Rated Input Voltage: 4.0V
  • Full Load Amps: 1.1A
  • Full Step Angle: 1.8° (200 Steps)
  • Unit Quantity: 1
  • Unit Type: Unit

PicClick Insights - 1 x NEMA 23 Stepper Motor, 200 Step, 4V@1.1A 3D Printer Arduino Raspberry Pi PicClick Exclusive

  •  Popularity - 32 watchers, 0.0 new watchers per day, 2,359 days for sale on eBay. Super high amount watching. 61 sold, 10 available.
  •  Best Price -
  •  Seller - 2,137+ items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.

People Also Loved PicClick Exclusive