5V-24V Motor Forward / Reverse Controller Timing Delay Time Cycles Relay New

£13.91 Buy It Now or Best Offer, FREE Shipping, 30-Day Returns, eBay Money Back Guarantee
Seller: ruyans ✉️ (123) 98.4%, Location: Sheffield, GB, Ships to: GB, Item: 395126053579 5V-24V Motor Forward / Reverse Controller Timing Delay Time Cycles Relay New.

Features:

  • Dual power supply (two power supplies cannot be powered at the same time): Power supply 1, DC 6.5-25V; Power supply 2, DC 5V   
  • Working current: (Normal Mode) standby current 41mA, working current 83mA; (Energy-Saving mode) Standby current 7mA, working current 44mA.   
  • There are three input control port: forward control(FWD), reverse control(REV), and stop control(STOP).   
  • Two input trigger modes, Low-Pulse trigger mode, Low-Level trigger mode   
  • Delay time: 0.1-999.9 seconds, 1-9999 seconds, 1-9999 minutes.   
  • Cycle times: no cycle, 2-99 cycles, always cycle.   
  • Three indicators: forward indicator(F LED), reverse indicator(R LED), stop indicator(S LED).   
  • Relay load current, recommended less than 5A.
  • This is a multi-function DC/AC motor forward and reverse controller with multiple control modes. Many control functions can be derived through reasonable settings.


Port:       
DC 5.5MM female : Power supply 1, DC 5V power supply. 
VIN: Power 2 positive, DC 6.5-25V power supply 
GND: Power supply 2 negative 
FWD: Forward input control (partial Function-Mode is invalid) 
REV: Reverse input control (partial Function-Mode is invalid) 
STOP : Stop input control (partial Function-Mode is invalid) 
M+: Motor positive  
M-: Motor negative 
P+: Positive terminal for motor power supply
P-: negative terminal for motor power supply

 

Specification:

Power supply: DC 6.5-25V, DC 5V

Working current: 83mA

Standby current: 41mA

Relay load current: <5A

Delay time: 0.1-999.9 seconds, 1-9999 seconds, 1-9999 minutes

Size: 8*5cm/3.2*2in
Weight: Approx. 51g/1.8oz

Trigger mode: 

1 low pulse trigger (falling edge trigger)

2 low level trigger (rising edge trigger)

   

Timer: 

T1: Forward timer

T2: Reverse timer

T3: Stop timer

Time unit : 0.1 second, 1 second, 1 minute

   

Relay action: 

Motor forward : Relay 1 is ON, relay 2 is OFF, and the F LED indicator is flashing.

Motor reverse : Relay 1 is OFF, relay 2 is ON, and the R LED indicator is flashing..

Motor stop   : Relay 1 is OFF, relay 2 is OFF, and the S LED indicator is flashing.

   

Factory settings: 

Press the "++" and "--" buttons simultaneously for 5 seconds.

   

Energy-saving mode: 

Press and hold the "OK" button for 5 seconds to enter the "Energy-saving mode". Press and hold the "OK" button again for 5 seconds to exit the "Energy-saving mode". Energy saving mode just turns off the digital tube and LED indicator, and other functions are normal.

 

Function mode: 

F-01

After power-on, the motor is forward T1 time; then the motor stops T3 time; then the motor reverse T2 time; so it is repeated Nx times. When the STOP port is triggered, the motor stops working immediately. (FWD, REV port is invalid)

  

F-02

This function is a F-01 variant. F-01 is run directly after power-on, but F-02 needs to trigger FWD or REV port to run.

  

F-11(Trigger  reversible 1)

Trigger the FWD port, the motor is forward T1 time, and automatically stops (in order to protect the motor, during the delay period, trigger the REV port to stop T3 time and then reverse T2 time, trigger FWD port to re-time T1).

Trigger the REV port, the motor is reverse T2 time, and automatically stops (in order to protect the motor, during the delay period, the FWD port is triggered to stop the T3 time and then the T1 time is forward, and the REV port is re-timed T2).

When the STOP port is triggered, the motor stops immediately, regardless of whether the motor is forward or reverse.

   

F-12(Trigger  reversible 2)

Trigger the FWD port, the motor is forward T1 time and stops automatically (during the delay period, except for triggering STOP port, the other ports are invalid).

Trigger the REV port, the motor is reverses T2 time, and automatically stops (during the delay period, except for triggering STOP port, the other ports are invalid).

When the STOP port is trigger, the motor stops immediately, regardless of whether the motor is forward or reverse.

   

F-21

When the FWD port is low level, the motor is forward, and after the FWD port is released, the motor stops.

When the REV port is low level, the motor is reversed, and after the REV port is released, the motor stops.

In this mode, the FWD and REV ports cannot be connected low level at the same time, and the STOP port is invalid.

  

F-22

When the FWD port is low level, the motor is forward, and after the FWD port is released, the motor stops.

When the REV port is low level, the motor is reversed, and after the REV port is released, the motor stops.

In this mode, the FWD and REV ports cannot be connected low level at the same time, triggering the STOP port, the motor stops immediately.

   

Parameter setting: 

There are three menus: Work Menu, Function Menu, Parameter Menu.

Note: When entering the "Function Menu" or "Parameter Menu", the module still works normally (countdown and the trigger is running normally). The set parameters are valid only after being powered on again.

   

1 Power on to enter the running state (Work Menu).

If the current function is F-01, then the motor direct run and the digital tube displays the countdown. F-01 is displayed after the operation is completed.

If the current function is other functions, such as F-11. Then the digital tube displays F-11. After the trigger, the digital tube displays the countdown. After the operation is completed, F-11 is displayed.

<Description: The forward countdown F LED indicator flashes, the reverse countdown R LED indicator flashes, and the S LED indicator flashes when stopped.|
Function   mode Digital   tube   display Setting   method
Function   01 F1-01 Short   press   the   "SET"   button   to   enter   the   setting   state,then   use   the   "++"button   and   the   "--"button   to   select   the   corresponding   sub-menu   setting,short   press   the"OK"   button   to   return   to   the   previous   menu
Function   02 F1-02
Function   011 F1-11
Function   012 F1-12
Function   21 F1-21
Function   22 F1-22
  2 In the running state(Work Menu), short press the SET button to enter the "Function Menu" (Above table).
Digital   tube   bit   1(parameters) bit2 bit3-4 parameter   definition default   parameter
1 -
00-99 Time   T1:single   digit   and   tens   digit 04
2 -
00-99 Time   TI:hundreds   digit   and   thousands   digit 00
3 -
00-99 Time   T2:single   digit   and   tens   digit 02
4 -
00-99 Time   T2:hundreds   digital   and   thousands   digita 00
5 -
00-99 Time   T3:single   digit   and   tens   digit 01
6 -
00-99 Time   T3:hundreds   digit   and   thousands   digit 00
7 -
01-03
01:0.1seconds
02:second
03:minute
time   unit 02
8 -
0-99 number   of   cycles 1
9 -
01-02
01   low   pulse   trigger
02   low   level   trigger
trigger   mode 01


Package list:

1 x Motor Controller board


1. Our listing price includes the value of goods,packaging cost,and export taxes,not including international duties. 2. duties,taxes,and charges are not included in the item price or shipping fee. 3. T he duties are buyers' responsibility .Please check with your country's customs office determine what these additional costs will be prior to your purchase. 4. All disputes arising from the duties will be submitted to ebay for solution.

1. Any questions, pls. contact us via ebay message or email us. We will reply your message within 48 hours. 

2. If you are satisfied with our service, pls. kindly leave us a positive feedback and give us the Detailed Seller Rating with all " 5 " in very area 3. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy.

We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders.

  • Condition: New
  • Brand: Unbranded
  • EAN: 7908194040266

PicClick Insights - 5V-24V Motor Forward / Reverse Controller Timing Delay Time Cycles Relay New PicClick Exclusive

  •  Popularity - 2 sold, 8 available. 1 watcher, 0.0 new watchers per day, 78 days for sale on eBay. Normal amount watching.
  •  Best Price -
  •  Seller - 123+ items sold. 1.6% negative feedback. Great seller with very good positive feedback and over 50 ratings.

People Also Loved PicClick Exclusive