DC 5V 4-phase 5-wire Stepper Motor+Driver Board+Remote Control Wireless

EUR 7,42 Buy It Now or Best Offer 10d 8h, FREE Shipping, 30-Day Returns, Pay with PayPal and you're fully protected.

Seller: Top-Rated Seller haiy_95inliao (56.520) 99.7%, Location: shenzhen, Ships to: Worldwide, Item: 223904221176 Features: Infrared remote controlMotor reversingMotor start stopMotor speed is adjustable (up to 14 laps per minute)Jog operation Press the button motor to release the button motor stopCruise round tripThe number of cruises can be customizedSpecify the number of stepsPower-off memory data is not lostTwo input ports with more than 20 input functionsSupport high-power driver TB6600 and other optical isolation pulse driver Note:This product is equipped with a motor, which can be used after being connected to the power supply; the power supply current must be greater than 800mA or it may not be activated in an instant; Motor parameters[Motor diameter] 28 mm[Output journal] Double D axis with a maximum diameter of 5 mm and a narrowest of 3 mm[Motor voltage] 4.2-5.1V[Step angle] 6.25*1/64[Deceleration ratio] 1:64[drive board volume] L25xW18xH13 mm[Drive board power supply] 4.2-5v DC[drive board start current] 1000mA Driver board function *All infrared remote control is more convenient to operate* Ultra-small size only L25xW18xH13mm is very convenient to place*Speed adjustable: one step from 1 millisecond to 59.99 seconds (+ - symbol)* Positive and negative control (ch-;ch+)*Start stop control (ch); press once to start and then stop again; this stop includes all the other modes of operation such as cruise*Specify the number of steps: Enter the first 6 digits of the key input 1 and press 65535 if the input value is greater than 65535. After setting the button 100+/200+ positive/reverse, press once to set the number of steps.*Cruise number: press the number key to input 3 digits and 6 digits; for example, cruise 3 times input: 300003; the maximum number is 65,534 laps. If it exceeds this value, it will run in an infinite loop. After setting, press the pause button to run, press once to run the cruise, press again to close the cruise*Auto mode: After setting the number of steps and the number of cruises, press '》 'pause button to start the round-trip motion, then automatically reverse the loop after the specified number of steps until the "" button is pressed again. The number stops or the number of cruises is completed. If you can't figure out whether it is open or not, you can press the CH button twice to force the operation to stop.* Can be input directly from the keyboard to input the speed value between 00001-59999*With memory, the last time the last setting is remembered after the new power is turned on. Remote control button function: Ch-: After the motor is pressed, the motor starts and reversesCh: Press once to start and then press to stop (stop including the running cruise will also be closed)Ch+: The motor starts and rotates after pressing : Change to jog reverse, press to release and then stop> : Press once to cruise and then press once to close-: Motor speed is reduced by 2 times+: Motor speed is doubledEQ: The recovery drive mode is 4-phase 5-wire motor mode, the speed is 2, the boot option is disabled.100+: Specify step reverse200+: Specify the number of steps to rotateDigital key combination inputThe beginning of the number 0: direct input speed, for example: 000001 speed is 1; 077777 speed is 65564;The beginning of the number 1: the specified number of steps such as: 100512 to 512 steps; 177777 is to take 65535 stepsThe beginning of the number 2 word: the specified number of laps and the beginning of the 1 word is used together with the equivalent of 1 prefix and 65535 numbers; for example, 4096 laps need to turn 4 laps can be set: enter 104096 and then enter 20004; input After entering the 3 prefix, set the number of good returns, press the green play button to run the cruise.The beginning of the number 3: specify the number of cruises such as 300002 cruise 2 times; 355555 cruise 55555 times; 377777 is an infinite loop Package include:1pcs Driver board1pcs Motor1pcs remote control Condition: New, current: 800mA, Model: Stepper Motor Driver, Country/Region of Manufacture: China, MPN: Does Not Apply, Brand: Unbranded, Input voltage: DC4.2~5.1V, EAN: 699948947203

PicClick Insights PicClick Exclusive
  •  Popularity - 516 views, 10.3 views per day, 50 days on eBay. Super high amount of views. 10 sold, 20 available.
  •  Price -
  •  Seller - 56.520+ items sold. 0.3% negative feedback. Top-Rated Seller! Ships on time with tracking, 0 problems with past sales.
Similar Items