Mdpe Push To Connect Push Fit Water Pipe Fittings

£2.59 Buy It Now, £4.36 Shipping, 14-Day Returns, eBay Money Back Guarantee
Seller: pipelineplus ✉️ (451) 100%, Location: Whitworth, Lancashire, GB, Ships to: GB & many other countries, Item: 174391789085 MDPE PUSH TO CONNECT PUSH FIT WATER PIPE FITTINGS. The professionals choice for MDPE Push-fit fittings for MDPE & PE pipe Benefits Pushfit fittings are quick and easy to use, with no nuts to lose or leave undone. The connections grip and seal on the pipe increases with water pressure and tensile load so that the pipe will burst or neck before the connection will fail. Technical Pressures: Working: 16 bar Test: 24 bar The pressures stated above apply with water temperatures up to 20°C Temperature: Up to 40° Performance specifications With reasonable care the simple Talbot Pushfit design minimises the risk of error during assembly. Talbot Pushfit fittings have excellent mechanical strength and can tolerate normal pipe imperfections as well as unsquare cut ends of pipe. To meet the requirements of the Water Regulations Advisory Scheme (WRAS) it is necessary to use an insert or liner with metric MDPE service pipe to BS 6572:1985, BS 6730 and HPPE to WIS 4-32-13 for below ground use in the UK. The liner is not an integral part of the Pushfit joint and for polyethylene pipe other than the PE pipe material shown above use of the liner is optional. If a liner is not used the connection will still substantially exceed most international performance requirements. Talbot recommend the use of a liner with all mains fittings for PE pipe of 63mm and above, although they are WRAS listed without liners. Suggested tightening torques for threaded ends of plastic

WRAS approved for use with potable water

What it means........

Any water fitting, which when installed, will carry or receive water from the public mains water supply in the UK, must comply with the Water Supply (Water Fittings) Regulations or Scottish Byelaws.  These require that a water fitting should not cause waste, misuse, undue consumption or contamination of the water supply and must be ‘of an appropriate quality and standard’. WRAS Approval is the easiest way to demonstrate compliance as it is granted directly by representatives of the water suppliers and is therefore accepted by every water supplier in the UK.

WRAS Product Approval: Whole products such as valves, fittings, boilers & showers undergo mechanical and water quality testing. This type of approval demonstrates full compliance with requirements of the regulations and byelaws, provided the fitting is installed according to any conditions given with the approval.

WRAS Material Approval: Non-metallic materials & components, such as rubber sheet material & ‘O’ rings, undergo testing only for their effects on water quality.  This type of approval demonstrates that the non-metallic material/component does not itself contaminate the water and therefore satisfies this particular requirement of regulations and byelaws

Extensive Range

If the size, or type of fitting is not listed here, please contact us as we can supply a wide range of other fittings from this range including:-

  • Female adapters
  • Reducing couplers
  • Tees with threaded off-takes
  • Elbows with threaded off-takes
  • Reducing tees
  • Wall plate elbows
  • Clamp saddles
  • Tapping saddles
  • Spare nuts, O rings, clamping rings, etc
  • Nut wrenches
  • Pipe cutters
  • Pipe in coils

We have MDPE pipe and fittings and other pipeline accessories on our other Ebay listings.

Please click on 'See other items' above to be taken to our other listings.

The not so small print...

All prices include VAT at the current rate

Our postage/carriage charges are for the UK mainland only excluding the Scottish Highlands.

For postage/carriage costs to the Scottish Highlands, Northern Ireland, and all UK Islands please contact us for a quotation

  • Condition: New
  • Fitting: Coupler
  • Size: 20mm
  • Features: Corrosion Resistant
  • Maximum Water Temperature: 122 °F (50 °C)
  • Modified Item: No
  • Unit Type: Unit
  • Standards: DIN 8076
  • Suitable For: Water
  • Country/Region of Manufacture: United Kingdom
  • Material: MDPE, Plastic, Polyethylene
  • Connection: Push-to-Connect
  • Brand: Talbot
  • Maximum Working Pressure: 16 bar
  • Type: Plastic pipe fittings

PicClick Insights - Mdpe Push To Connect Push Fit Water Pipe Fittings PicClick Exclusive

  •  Popularity - 81 watchers, 0.1 new watchers per day, 1,324 days for sale on eBay. Super high amount watching. 65 sold, 10 available.
  •  Best Price -
  •  Seller - 451+ items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.

People Also Loved PicClick Exclusive