3Axis Nema34HS5435C-02B2 Stepper Motor Dual Shaft 1600oz.in 3.5A&Driver CNC Kit

EUR 385,67 Buy It Now or Best Offer 27d 6h, FREE Shipping, 14-Day Returns, Pay with PayPal and you're fully protected.

Seller: Top-Rated Seller longsmotor (2.059) 99.6%, Location: Denmark, Ships to: Worldwide, Item: 163668613109 This item will be shipped from our EU warehouse by DHL or GLS to European Union Customers.For European Union Customers, it will be faster to receive the parcel. What's in Box? 3 pcs Nema 34 stepper motor 34HS5435C-02B2 with dual shaft, 1600oz.in, biloar3 pcs Stepper motor driver DM860A , peak 7.8A 24-80VDC3 pcs Power supply 350W(60VDC/5.8A)1 pc Breakout Board & Parallel cable ( free offering when you buy all above)Detailed information :1. Nema 34 stepper motor:Technical SpecificationsPart No.: 34HS5435C-02B2Frame Size: NEMA34Phase: 2 PhaseStep Angle: 1.8 degreeCurrent: 3.5ARated Voltage: 5.6VResistance: 1.6 Ohm/phaseInductance: 22mH/phaseHolding torque: 1600oz-in (10.5N.m)Detent torque: 24.5N.cmRotor inertia: 3600g.cm²Number of wire leads: 4 (Red A+ ,Green A- ,Yellow B+ ,Blue B-)Weight: 5kgLength: 151mmThe diameter for motor shaft is 14mm2. Stepper motor driver DM860AIntroduction:DM860A is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter and less than 8.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on.Features:l High performance, low pricel Average current control, 2-phase sinusoidal output current drivel Supply voltage from 24VDC to 80VDCl Opto-isolated signal I/Ol Overvoltage, under voltage, overcorrect, phase short circuit protectionl 14 channels subdivision and automatic idle-current reductionl 8 channels output phase current settingl Offline command input terminall Motor torque is related with speed, but not related with step/revolutionl High start speedl High hording torque under high speed Electrical specification: Input voltage24-80VDCInput current< 6AOutput current2.8A~7.8AConsumptionConsumption:80W; Internal Insurance:10ATemperatureWorking Temperature -10~45℃;Stocking temperature -40℃~70℃HumidityNo condensation, no water dropletsgasProhibition of combustible gases and conductive dustweight500G Pins assignments and description: 1) Connector Pins Configurations Pin Function Details PUL +,PUL-Pulse signal, PUL+ is the positive end of pulses input pin PUL- is the negative end of pulse input pin DIR+,DIR-DIR signal: DIR+ is the positive end of direction input pin DIR- is the negative end of direction input pinENBL+ Enable signal: ENBL+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver.ENBL-ENBL- is the negative end of direction input pin. Usually left unconnected (enabled) 2) Pins wiring diagram:PC’s control signals can be active in high and low electrical level. When the high electrical level is active,all control negative signals will be connected together to GND. When low electrical level is active, allcontrol positive signals will be connected together to public port. Now give two examples( Open collector&PNP), please check them: Fig 1. Input port circuit (Yang connection) PC open connector output Fig. 2 Input port circuit ( Yin connection) PC PNP outputNote: When VCC=5V, R=0 When VCC=12V, R=1K, >1/8W When VCC=24V, R=2K,>1/8WR must connect in the control signal part . 3.Function choice ( Using DIP pins to achieve this function) 1) Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table: SW5ONOFFONOFFONOFFONOFFONOFFONOFFONOFFSW6ONONOFFOFFONONOFFOFFONONOFFOFFONONSW7ONONONONOFFOFFOFFOFFONONONONOFFOFFSW8ONONONONONONONONOFFOFFOFFOFFOFFOFFPULSE/REV 2) Standstill current settingSW4 is used for this purpose. OFF meaning that the standstill current is set to be half of the selected dynamiccurrent and ON meaning that standstill is set to be the same as the selected dynamic current. 3) Output current setting:The first three bits (SW 1, 2, 3)of the DIP switch are used to set the dynamic current. Select a settingClosest to your motor’s required current Output current (A)SW1SW2SW3PEAKRMSONONON2.802.00OFFONON3.502.50ONOFFON4.203.00OFFOFFON4.903.50ONONOFF5.704.00OFFONOFF6.404.60ONOFFOFF7.005.00OFFOFFOFF7.805.60 4) Semi-flow function:Semi-flow function is that there is not step pulse after200 ms, the driver output current automaticallyreduced to 40% of rated output current, which is used to prevent motor heat. 4. Pins of motor & power: Motor and power pins1A+Motors wiring 2A-3B+4B-5,6DC+ DC-Power supplyPower supply :DC24-80VDCThe peak input current can not up to 6A 3.Power supply:The power of this power supply is 350Watts, and the output voltage/current is 60V. 4.Breakout board Description: • Built in DB25 male connector. • DB25 Output Pin:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17. • DB25 Input Pin: P10,P11,P12,P13,P15. • DB25 GND Pin: P18-P25. • Power supply: +5V DC. • Built in C-class Optical-coupler. • High quality with Surface-mount Tech P2 P3 is set to X-axis for the X-axis pulseP4 P5 is set to Y-axis, Y axis pulseP6 P7 is set to Z-axis Z-axis pulseThe other can be set to A B C axisA-axis pulse P8 P9 is set as the A axisP14 is set to B-axis B-axis pulse P1P16 P17 is set to C-axis, C axis pulseCan also be set to the spindle control signal \ electrical permitInput interface for the P10 P11 P12 P13 P15 WIRING DIAGRAM:Application: Our Stepper Motors are used on small to mid-sized CNC mills or milling machines, CNC lathes, Pick-n-place machines,Laser Engravers and Laser Cutters, Vinyl Sign Cutters, CNC Plasma Cutters, and CNC Foam Cutters. Carver machine ,Dispenser,Automazation,3D Printer,Stage lighting,instrument,laser equipment,scanner and so on.These motors have been used in precision telescope positioning systems and robots. Condition: New, Non-Domestic Product: No, Model: 34HS5435C-02B2&DM860A&350W-60V, Modified Item: No, Country/Region of Manufacture: China, Custom Bundle: No, Wiring Configuration: 4-Wire Bipolar, MPN: 036876502370, Brand: LONGS MOTOR

PicClick Insights PicClick Exclusive
  •  Popularity - 640 views, 1.6 views per day, 400 days on eBay. Super high amount of views. 0 sold, 66 available.
  •  Price -
  •  Seller - 2.059+ items sold. 0.4% negative feedback. Top-Rated Seller! Ships on time with tracking, 0 problems with past sales.
Similar Items