3Axis Nema23 stepper motor 425oz-in dual shaft 23HS9430B Driver DM542A CNC KIT

EUR 189,75 Buy It Now or Best Offer 10d 20h, FREE Shipping, 30-Day Returns, Pay with PayPal and you're fully protected.

Seller: Top-Rated Seller longsmotor (1.968) 100%, Location: Denmark, Ships to: Worldwide, Item: 161380427149 This item will be shipped from our EU warehouse by DHL or GLS to European Union Customers. For European Union Customers, it will be faster to receive the parcel. This item includes:3 pcs Nema 23 stepper motor 23HS9430B 425oz.in, 3.0A, dual shaft 3 pcs Stepper motor driver DM542A, 24-50VDC 1 pc Power Supply 350Watts(36VDC/9.7A) 1 pc parallel cable & 1 pc breakout board Detailed information: 1. Nema 23 stepper motor Technical Specifications Part No.: 23HS9430BFrame Size: NEMA23Phase: 2 PhaseStep Angle: 1.8 degreeCurrent: 3 ARated Voltage: 4.8VResistance: 1.6Ohm/phaseInductance: 6.8 mH/phaseHolding torque: 425 oz-in (2.8N.m)Detent torque: 12N.cmRotor inertia: 800 g.cm²Number of wire leads: 4Weight: 1.7 kgLength: 112 mmShaft: Dual ShaftMatched drive: DM542A (it uses DM542A driver, you can search it on my store) 2. Stepper motor driver DM542ADM542A is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 18VDC to 50VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is smiliar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on.Features:l High performance, low pricel Average current control, 2-phase sinusoidal output current drivel Supply voltage from 18VDC to 50VDCl Opto-isolated signal I/Ol Overvoltage, under voltage, overcorrect, phase short circuit protectionl 15 channels subdivision and automatic idle-current reductionl 8 channels output phase current settingl Offline command input terminall Motor torque is related with speed, but not related with step/revolutionl High start speedl High hording torque under high speed Electrical specification: Input voltage18-50VDCInput current< 4AOutput current1.0A~4.2AConsumptionConsumption:80W; Internal Insurance:6ATemperatureWorking Temperature -10~45℃;Stocking temperature -40℃~70℃HumidityNo condensation, no water dropletsgasProhibition of combustible gases and conductive dustweight300GS Pins assignments and description: 1) Connector Pins Configurations Pin Function Details PUL +,PUL-Pulse signal, PUL+ is the positive end of pulses input pin PUL- is the negative end of pulse input pin DIR+,DIR-DIR signal: DIR+ is the positive end of direction input pin DIR- is the negative end of direction input pinENBL+ Enable signal: ENBL+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver.ENBL-ENBL- is the negative end of direction input pin. Usually left unconnected (enabled) 2) Pins wiring diagram:PC’s control signals can be active in high and low electrical level. When the high electrical levelis active, all control negative signals will be connected together to GND. When low electricallevel is active, all control positive signals will be connected together to public port. Now givetwo examples( Open collector &PNP), please check them: Fig 1. Input port circuit (Yang connection) PC open connector output Fig. 2 Input port circuit ( Yin connection) PC PNP outputNote: When VCC=5V, R=0 When VCC=12V, R=1K, >1/8W When VCC=24V, R=2K,>1/8WR must connect in the control signal part . Function choice ( Using DIP pins to achieve this function)1) Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table: SW5OFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFSW6ONOFFOFFONONOFFOFFONONOFFOFFONONOFFOFFSW7ONONONOFFOFFOFFOFFONONONONOFFOFFOFFOFFSW8ONONONONONONONOFFOFFOFFOFFOFFOFFOFFOFFPULSE/REV400800160032006400128002560010002000400050008000100002000025000 2) Standstill current settingSW4 is used for this purpose. OFF meaning that the standstill current is set to be half of theselected dynamic current and ON meaning that standstill is set to be the same as the selecteddynamic current. 3) Output current settingThe first three bits (SW 1, 2, 3)of the DIP switch are used to set the dynamic current.Select a setting Closest to your motor’s required current Output current (A)SW1SW2SW3PEAKRMSONONON1.000.71OFFONON1.461.04ONOFFON1.911.36OFFOFFON2.371.69ONONOFF2.842.03OFFONOFF3.312.36ONOFFOFF3.762.69OFFOFFOFF4.203.00 4) Semi-flow functionSemi-flow function is that there is not step pulse after 500 ms, the driver output currentautomatically reduced to 70% of rated output current, which is used to prevent motor heat. Pins of motor & power: Motor and power pins1A+Motors wiring 2A-3B+4B-5,6DC+ DC-Power supplyPower supply :DC18-50VDC 3. Power supply The power is 350Watts, and the output voltage is 36VDC. 4. Breakout boardDescription:• Built in DB25 male connector.• DB25 Output Pin:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17.• DB25 Input Pin: P10,P11,P12,P13,P15.• DB25 GND Pin: P18-P25.• Power supply: +5V DC.• Built in C-class Optical-coupler.• High quality with Surface-mount Tech. Wring Diagram: Condition: New, Country/Region of Manufacture: China, Model: 23HS9430B&DM542A&350W-36V&BB, Wiring Configuration: 4-Wire Bipolar, MPN: C01704A56473, Full Step Angle: 1.8° (200 Steps), Shaft Diameter: 8mm, Holding Torque: 425oz-in, Brand: LONGS MOTOR

PicClick Insights PicClick Exclusive
  •  Popularity - 9.367 views, 4.6 views per day, 2.031 days on eBay. Super high amount of views. 58 sold, 55 available.
  •  Price -
  •  Seller - 1.968+ items sold. 0% negative feedback. Top-Rated Seller! Ships on time with tracking, 0 problems with past sales.
Similar Items