【EU Free】5Axis Nema 34 CNC Stepper Motor 1600OZ-IN Spindle &2 Nema23,425oz-in

EUR 358,16 Buy It Now 3d 7h, EUR 10,13 Shipping, 30-Day Returns, Pay with PayPal and you're fully protected.

Seller: wantaimotor (5.157) 98.8%, Location: Warsaw, Ships to: Worldwide, Item: 183797998522 Great News from Wantaimotor! Ship from our German warehouse, Customers From All EU Countries can be shipped as well, no taxes, no damage, very fast, please don't hesitate :) The item includes: 2 PCS Nema 34 stepper motor with 1600oz-in for Single shafts, 3 PCS Nema 23 Stepper Motor with 425oz-in for Dual shafts, 2 PCS DQ860MA Stepper Driver with 80VDC,7.8A, 256 Microstep, 3 PCS DQ542MA Stepper Driver with 50VDC,4.2A,128 Microstep, 1 PC 350W,48VDC,7.3A Power Supplier, 1 PC 350W,36VDC,7.3A Power Supplier, 1 PC Breakout Board + 1 Cable. High Quality Porducts!!!1, Stepper Motor Part No.: 85BYGH450C-012 single shaftsFrame Size: NEMA34Step Angle: 1.8 degreeVoltage: 5.6 VCurrent: 3.5A/phaseResistance: 1.6 Ohm/phaseInductance: 22 mH/phaseHolding torque: 11.5N.m 1600oz-in (in Bipolar connection)Rotor inertia: 3600g-cm2Number of wire leads: 4Weight: 5.0 kgsLength: 151mm Note: Nema 34 Stepper Motor with 1600oz-in holding torque on single shaft, front shaft length is 37mm with 25mm flats length, the diameter for motor shaft is 14mm. RED A+ GREEN A- YELLOW B+ BLUE B- If you want the drawing or Torque-Frequency Characters, please contact us, we will send to you by Email. thanks ! 2.Stepper Driver DQ860MA It is an economical microstepping driver based on patented technology of Wantai. It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique ,it can output more speed and torque from the same motor,compared with traditional drivers ,such as L/R drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple,therefore less motor heating is achieved.FeaturesLow cost and good high-speed torque14 selectable resolutionsSupply voltage up to +80VD Suitable for-2-phase and 4-phase motorsOutput current up to 7.8A ,rated current to 5.86A, 256MicrostepDip switch current setting 8different valuesOptically isolated input signalsPulse frequency up to 200KHz Automatic idle-current reductionSmall size (107*97*48),Weight:0.6KGS Electrical Specifications (Tj=25℃)Paraneters SD-2H086MBMinTypicalMaxUnitOutput current 1.29-5.86(rms)ASupply voltage((DC) 206880VDCLogic signal current61030mAPulse input freauency0-200KHzIsolation resistance500 MΩ 3, Stepper MotorTechnical SpecificationsPart No.: WT57STH115-3004B dual shaftsFrame Size: NEMA23Step Angle: 1.8 degreeVoltage: 6.3VDCCurrent: 3.0 A/phaseResistance: 2.1 Ohm/phaseInductance: 9mH/phaseHolding torque: 30Kg-cm 425oz-inRotor inertia: 810 g-cm2Detent torque: 0.89 kg-cmNumber of wire leads: 4Weight: 1.55KGSLength: 115mm 4, DQ542MA driver DQ542MA is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 18VDC to 50VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mmoutside diameter and less than 4.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DQ542MA run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, Computer embroider machine, packing machines and so on.Features:l High performance, low pricel Average current control, 2-phase sinusoidal output current drivel Supply voltage from 18VDC to 50VDCl Opto-isolated signal I/Ol Overvoltage, under voltage, overcorrect, phase short circuit protectionl 15 channels subdivision and automatic idle-current reductionl 8 channels output phase current settingl Offline command input terminall Motor torque is related with speed, but not related with step/revolutionl High start speed High hording torque under high speed5, Power Suppy 350W,48VDC,7.3A,350W,36VDC,9.8A,6, Breakout Board DB25Description:Built in DB25 male connector. We ship Woldwide! Send by express shipping, like EMS, TNT, DHL, FEDEX and so on! We product all kinds of motors & driver. And we can manufacture products according to our customer's design.Currently we are looking for qualified stocking distributors with competitive price and good discount in WORLDWIDE for mutually beneficial long-term relationship. We try our best to support our distributors and business partners to develop more market percentage.Please join us, let’s create the glorious future together! Wantai Electrical Appliance Co., Ltd Condition: New, Country/Region of Manufacture: Germany, Current Type: DC, Unit Quantity: 10pcs, Wiring Configuration: 4-Wire Bipolar, Insulation Class: B (Max 130°C), MPN: Does Not Apply, Full Step Angle: 1.8° (200 Steps), IP Rating: IP54, Unit Type: kg, Brand: wantai motor, Type: Stepper Motor

PicClick Insights PicClick Exclusive
  •  Popularity - 223 views, 0.7 views per day, 333 days on eBay. Super high amount of views. 0 sold, 27 available.
  •  Price -
  •  Seller - 5.157+ items sold. 1.2% negative feedback. Great seller with very good positive feedback and over 50 ratings.
Similar Items