PVC Metric Plumbing Fittings Pipe For Aquarium Fish Tank Pond Solvent Weld Please read full description below before purchasing.

£3.49 Buy It Now, FREE Shipping, 60-Day Returns, eBay Money Back Guarantee
Seller: Top-Rated Seller finest-filters1 ✉️ (369,190) 99.7%, Location: Widnes, GB, Ships to: GB, Item: 353631032164 PVC Metric Plumbing Fittings Pipe For Aquarium Fish Tank Pond Solvent Weld.

PVC Metric Plumbing Fittings Pipe For Aquarium Fish Tank Pond Solvent Weld

Our metric PVC Aquarium / Pond solvent weld plumbing is ideal for various plumbing jobs in your aquarium or pond. Our pipe fittings are available in a range of sizes including 20mm,  25mm, 32mm, 40mm and 50mm.

Please Note: Diameters of the fittings is the internal sizes, diameter of the Pipe lengths are the external sizes.

All of the dimensions for the fittings will fit the corresponding size piping, e.g. pipe with a 40mm external diameter will fit into our 40mm fittings.

Due to the size of the lengths of pipe, they are shipped separately to the fittings when purchased together. Please check your order for two tracking numbers upon purchase.

The tracking numbers will be joined together and should end with "GB". These can be split apart and tracked individually on Royal Mail's website.

Please select the required fitting type from the drop-down menu then select the size of fitting required.

Straight Coupling – Used for permanently joining two pieces of equally sized pipe in a straight line.

45 Degree Elbow –  Used for permanently joining two pieces of equally sized pipe at a 45-degree angle.

90 Degree Elbow –  Used for permanently joining two pieces of equally sized pipe at a 90-degree angle.

90 Degree Swept Elbow  - Used to create a less harsh 90-degree angle bend between two pieces of equally sized pipe pieces. The use of a swept elbow helps reduce loss of flow rate compared to a standard 90 degree elbow.

Tee Piece – Used for permanently joining three pieces of equally sized pipe at 90-degree angles.

End Cap – Used to permanently seal the end of a piece of pipe.

Union Connector – Used for joining two pieces of equally sized pipe in a straight line but can be unscrewed later for easy access / maintenance.

None Return Valve – Used to prevent water back siphoning down the pipe when water pump is stopped. Ideal for applications where there is limited capacity in the sump to accept excess water.

Pipe Clip – Used to secure pipe to wall / cabinetry to hold securely in place.

Double Union Ball Valve – Used to regulate or stop water flow down the pipe. The unions on both sides allow the valve to be easily disconnected for maintenance and cleaning.

Simple Ball Valve – Used to regulate or stop water flow down the pipe.

Gate Valve - Used to finely control water flow. The most accurate type of valve, ideal for use on drain lines to control water level in aquarium / weir.

PLEASE NOTE: We stock two types of tank connector. (Tank Connector Bulkhead and Bonded Tank Connectors). The tank connector bulkhead REDUCE the internal diameter of the pipe through the fitting, which may restrict water flow so we recommend upsizing if required. The Bonded Tank Connectors do not reduce the internal diameter of the fitting, so will accommodate a higher flow rate.

Tank Connector Bulkhead – Used to make a watertight connection between aquarium and the pipe fittings. Please see note below on tank connector internal diameter sizes and recommended hole drill size range.

Please Note: Due to the design, these standard tank connector bulkheads reduce the diameter in the centre of the connector. Please see detailed dimensions below:

20mm Bulkhead centre diameter: 12mm. Will accept a drilled hole of 20mm-30mm

25mm Bulkhead centre diameter: 16mm. Will accept a drilled hole of 25mm-35mm

32mm Bulkhead centre diameter: 24mm. Will accept a drilled hole of 32mm-42mm

40mm Bulkhead centre diameter: 31mm. Will accept a drilled hole of 40mm-50mm

50mm Bulkhead centre diameter: 37mm. Will accept a drilled hole of 48mm- 58mm

If a larger bore diameter is required, we recommend upsizing on the tank connector bulkhead and using reducing spigots in each end to maintain a constant internal diameter.

Bonded Tank Connector - A premium tank connector which does not reduce the internal diameter on both sides of the tank connector. They have a external socket on one side and threaded BSP thread on the other.

20mm - (20mm pipe can be bonded to the inside of both sides of this fitting) The stem side of the fitting has a measurement of 25mm, therefore you can also connect 25mm pipe to the stem side by using a 25mm joint socket. The thread side on this fitting is a male 3/4" BSP thread. If you wish to connect to the thread then you require a fitting with a female 3/4" BSP socket. This fitting will accept a drilled hole size of 27-30mm

25mm - (25mm pipe can be bonded to the inside of both sides of this fitting) The stem side of the fitting has a measurement of 32mm, therefore you can also connect 32mm pipe to the stem side by using a 32mm joint socket. The thread side on this fitting is a male 1" BSP thread. If you wish to connect to the thread then you require a fitting with a female 1" BSP socket. This fitting will accept a drilled hole size of 34-39mm

32mm - (32mm pipe can be bonded to the inside of both sides of this fitting) The stem side of the fitting has a measurement of 40mm, therefore you can also connect 40mm pipe to the stem side by using a 40mm joint socket. The thread side on this fitting is a male 1 1/4" BSP thread. If you wish to connect to the thread then you require a fitting with a female 1 1/4" BSP socket. This fitting will accept a drilled hole size of 42-49mm

40mm - (40mm pipe can be bonded to the inside of both sides of this fitting) The stem side of the fitting has a measurement of 50mm, therefore you can also connect 50mm pipe to the stem side by using a 50mm joint socket. The thread side on this fitting is a male 1 1/2" BSP thread. If you wish to connect to the thread then you require a fitting with a female 1 1/2" BSP socket. This fitting will accept a drilled hole size of 54-60mm

50mm - (50mm pipe can be bonded to the inside of both sides of this fitting) The stem side of the fitting has a measurement of 63mm, therefore you can also connect 63mm pipe to the stem side by using a 63mm joint socket. The thread side on this fitting is a male 2" BSP thread. If you wish to connect to the thread then you require a fitting with a female 2" BSP socket. This fitting will accept a drilled hole size of 63-69mm

4 Way Cross – Used for permanently joining four pieces of equally sized pipe at 90-degree angles.

None Return Strainer – Used to strain large pieces of debris and prevent items entering the plumbing system. Please Note: These strainers have a none return valve built into them, which can be removed if not required.

Solvent Weld Glue – Used to permanently glue pipe and fittings together. Supplied in a 120g tub complete with application brush.

PVC Pipe – 1.3m (130cm / 1300mm) – Hard PVC solvent weld pipe compatible with all of our fittings. Due to shipping regulations – we can only supply pipe in maximum lengths of 1.3 metres. If a longer piece is required, we recommend ordering multiple units and connecting the pipe with a straight coupling or union connector.

PVC Pipe –  0.4m (40cm / 400mm) – Hard PVC solvent weld pipe compatible with all of our fittings.

Hose tail Spigot –  PLEASE NOTE: The fitting end of the spigots are in external diameter. E.g: 20mm would fit inside a 20mm coupling.  Used to connect a flexible hose to the PVC plumbing. Ideal for use with return pumps where direct connection to the hard plumbing is not possible and must be achieved with a flexible hose.

Reducing Bush – Used to reduce pipe diameter. The bush simply solvent welds directly onto each end of the pipe.

Reducing Connector – Used to reduce pipe diameter. Provides less pressure loss than a reducing bush due to gradual reduction to the smaller size.

Threaded Male Connector – Threaded male section which is ideal for screwing into pumps or other pieces of equipment.

Threaded Female Connector – Threaded female section which is ideal for screwing onto pumps or pieces of equipment.

  • Condition: New
  • Fitting Type: Straight Coupling
  • Size: 20mm
  • Material: PVC
  • Type: Adapter
  • Brand: Finest-Filters

PicClick Insights - PVC Metric Plumbing Fittings Pipe For Aquarium Fish Tank Pond Solvent Weld PicClick Exclusive

  •  Popularity - 1,193 watchers, 1.3 new watchers per day, 954 days for sale on eBay. Super high amount watching. 238 sold, 10 available.
  •  Best Price -
  •  Seller - 369,190+ items sold. 0.3% negative feedback. Top-Rated Plus! Top-Rated Seller, 30-day return policy, ships in 1 business day with tracking.

People Also Loved PicClick Exclusive